The GST JP5000 HVOF Spray Gun is a machine-mounted liquid-fuel High-Velocity Oxygen Fuel (HVOF) torch designed for high-rate deposition of dense carbide, cermet, metal and alloy coatings. The JP5000 architecture uses kerosene and oxygen to generate a high-pressure combustion jet and is widely used for demanding wear, corrosion and dimensional-restoration applications.
The GST JP5000 HVOF Spray Gun is a machine-mounted liquid-fuel High-Velocity Oxygen Fuel (HVOF) torch designed for high-rate deposition of dense carbide, cermet, metal and alloy coatings. The JP5000 architecture uses kerosene and oxygen to generate a high-pressure combustion jet and is widely used for demanding wear, corrosion and dimensional-restoration applications.
Kerosene and oxygen are burned in the combustion chamber and accelerated through a converging-diverging nozzle. Powder is introduced radially through ports located downstream of the nozzle throat, where the pressure is lower. This injection arrangement promotes uniform powder distribution, controlled heating and high particle velocity while reducing the time that the feedstock is exposed to the hottest part of the flame.
The high-pressure design supports very dense coatings with low oxide content and high bond strength. The JP5000 is particularly effective for WC-Co, WC-CoCr, Cr3C2-NiCr and other HVOF materials and can achieve high powder throughput for production coating. Interchangeable 4, 6 and 8 inch barrel configurations allow the gun setup to be adapted to the coating material and process requirements.
The GST JP5000 is intended for automated installation with industrial robots, manipulators, lathes and complete GST HVOF coating cells. GST also supplies compatible gun components, barrel assemblies, water-cooling parts, powder-feed hardware, check valves, seals and other maintenance items for long-term system support.
Key benefits
- Liquid-fuel HVOF architecture using kerosene and oxygen for high-pressure, high-velocity coating deposition.
- Radial powder injection downstream of the nozzle throat supports uniform heating and high particle velocity.
- High powder throughput for productive coating of large parts and production batches.
- Dense, low-oxide carbide and alloy coatings with high hardness and bond strength when properly qualified.
- Interchangeable 4, 6 and 8 inch barrel assemblies provide process flexibility for different powders and applications.
- Efficient water cooling supports long industrial spray cycles and reliable operation.
- Machine-mounted design is suitable for robots, manipulators, lathes and automated HVOF coating cells.
- Extensive GST-compatible spare-parts range supports maintenance, repair and lifecycle operation.
Optional Accessories and Consumables
The GST JP5000 HVOF Spray Gun is supported by a broad range of compatible wear parts, barrel configurations, powder-feed components and maintenance items for process setup and lifecycle service.
- 4 / 6 / 8 inch barrel assemblies and barrel holders
- Interconnector and combustion-nozzle components
- Coaxial fuel tube assembly
- Spark plug assembly and ignition components
- Powder-feed splitter, feed tubes and injector fittings
- Water jacket, water baffle and cooling components
- Oxygen and fuel check valves with adapters and nipples
- Gun mounting fixtures and robotic brackets
- Replacement O-rings, seals, screws and maintenance parts
GST supplies JP5000-compatible spare parts and consumables for routine maintenance and overhaul. Published performance values in the specification table are reference values for the established Model 5220 / JP5000 architecture; the final GST configuration and operating limits should be confirmed in the quotation and process documentation.
| No. | Article | Name | OEM Article No. |
|---|---|---|---|
| 1 | ST310062 | Rear cover | 310.062 |
| 1a | ST310004 | Rear cover dowel pin | 310.004 |
| 2 | ST310082 | Coaxial fuel tube assembly | 310.082 |
| 3 | ST310074 | Spark plug assembly | 310.074 |
| 4 | ST310025 | O-Ring, coaxial fuel tube, rear | 310.025 |
| 5 | ST310034 | O-Ring, coaxial fuel tube, front | 310.034 |
| 6 | ST310086 | Combustion pressure tube assembly | 310.086 |
| 7 | ST310045 | Nut, stabilizer to water jacket | 310.045 |
| 8 | ST310103 | Oxygen check valve | 310.103 |
| 8a | ST310010 | Nipple, 1/4" Oxygen check valve to stabilizer | 310.010 |
| 8b | ST310013 | Adapter, 1/4" NPT | 310.013 |
| 9 | ST310042 | Fuel check valve | 310.042 |
| 9a | ST310009 | Nipple, 1/8" Fuel check valve to stabilizer | 310.009 |
| 9b | ST310007 | Adapter 1/8" NPT | 310.007 |
| 10 | ST310005 | Screw, ground cable | 310.005 |
| 11 | ST310069 | Coaxial stabilizer assembly | 310.069 |
| 11a | GST-201071 | Rear gun body | - |
| 12 | ST310030 | O-Ring, stabilizer, back | 310.030 |
| 13 | ST310101 | O-Ring, comb. chamber to stab. spacer | 310.101 |
| 14 | ST310033 | O-Ring, stabilizer, front | 310.033 |
| 15 | ST310060 | Combustion chamber | 310.060 |
| 16 | ST310031 | O-Ring, combustion chamber | 310.031 |
| 17 | ST310058 | Water jacket | 310.058 |
| 18 | ST310018 | Fitting, swivel, water in, 3/8" MNPT | 310.018 |
| 19 | ST310017 | Fitting, water out | 310.017 |
| 20 | ST310063 | Front cover plate | 310.063 |
| 21 | ST310002 | Screw, front cover plate | 310.002 |
| 22 | ST310102 | O-Ring, interconnector | 310.102 |
| 23 | ST310059 | Interconnector | 310.059 |
| 24 | ST310044 | Nut, interconnector to water jacket | 310.044 |
| 25 | ST310078 | 4" Barrel w/O-Rings | 310.078 |
| 25 | ST310079 | 6" Barrel w/O-Rings | 310.079 |
| 25 | ST310080 | 8" Barrel w/O-Rings | 310.080 |
| 26 | ST310032 | O-Ring, barrel, back | 310.032 |
| 27 | ST310035 | O-Ring, barrel, front | 310.035 |
| 28 | ST310052 | 4" Water return tube | 310.052 |
| 28 | ST310053 | 6" Water return tube | 310.053 |
| 28 | ST310054 | 8" Water return tube | 310.054 |
| 29 | ST310026 | O-Ring, water return tube to water jacket | 310.026 |
| 30 | ST310100 | O-Ring, water return tube/barrel holder | 310.100 |
| 31 | ST310003 | Screw, water return to barrel holder | 310.003 |
| 32 | ST310047 | 4" Barrel holder | 310.047 |
| 32 | ST310048 | 6" Barrel holder | 310.048 |
| 32 | ST310049 | 8" Barrel holder | 310.049 |
| 33 | ST310065 | Water baffle | 310.065 |
| 34 | ST310070 | 4" Barrel assembly | 310.070 |
| 34 | ST310071 | 6" Barrel assembly | 310.071 |
| 34 | ST310072 | 8" Barrel assembly | 310.072 |
| 35a | ST310061-01 | Feed tube insert | 310.061-01 |
| 35b | ST310091-01 | Fitting, powder port 1/4" | 310.091-01 |
| 35c | ST310019 | Nut, 1/4" tube | 310.019 |
| 35d | ST310008 | Ferrule, plastic, 1/4" tube | 310.008 |
| 35e | ST310016 | Powder feed splitter | 310.016 |
| 36 | ST310043 | Nut, barrel holder to interconnector | 310.043 |
| 37 | ST310029 | O-Ring, barrel holder | 310.029 |
Applications
The GST JP5000 HVOF Spray Gun is designed for high-productivity deposition of wear-, corrosion- and erosion-resistant coatings in demanding industrial applications, including:
- WC-Co and WC-CoCr coatings on landing gear, hydraulic rods, shafts and high-wear aerospace components.
- Cr3C2-NiCr coatings for high-temperature wear, erosion and corrosion protection.
- Hydropower components such as Pelton wheels, guide surfaces and wear areas.
- Valve balls, gates, seats and pump components for oil, gas and process industries.
- Wear-resistant coatings on rolls, plungers, sleeves, mandrels and extrusion components.
- Corrosion-resistant nickel- and cobalt-alloy coatings for aggressive service environments.
- Thick protective and dimensional-restoration coatings where high deposition productivity is required.
- Hard-chrome replacement coatings on qualified aerospace, hydraulic and industrial components.
FAQ
What is the GST JP5000 HVOF Spray Gun used for?
The JP5000 is used for high-productivity HVOF deposition of dense carbide, cermet, metal and alloy coatings. Typical applications include landing gear, hydraulic rods, valves, pumps, hydropower parts, rolls and other severe-wear components.
Which fuel does the JP5000 use?
The JP5000 is a liquid-fuel HVOF gun. It uses kerosene, typically K-1 / 1-K, together with oxygen to generate the high-pressure combustion jet.
How is powder injected in the JP5000?
Powder is injected radially through ports downstream of the combustion-nozzle throat. This lower-pressure injection location promotes even powder distribution and controlled particle heating.
What barrel lengths are available?
The established JP5000 / Model 5220 architecture uses interchangeable 4, 6 and 8 inch barrel assemblies. The barrel is selected according to powder type, particle size, required particle state and coating specification.
What coating materials can be sprayed with the JP5000?
The gun is particularly well suited to WC-Co, WC-CoCr, Cr3C2-NiCr and other carbide or cermet powders, as well as metallic, nickel-based, cobalt-based and other alloy feedstocks qualified for HVOF spraying.
What is the maximum spray rate of the JP5000?
The JP5000 supports powder spray rates up to approximately 20 lb/h (151 g/min). Actual feed rate depends on powder characteristics, barrel configuration and qualified process parameters.
How is the JP5000 cooled?
The gun is water cooled. It requires approximately 7-12 gpm (26.5-45.4 l/min) cooling-water flow at 100-150 psi (6.8-10.2 bar). Final utility requirements should be confirmed for the supplied GST configuration.
Can GST supply JP5000 spare parts and maintenance components?
Yes. GST supplies compatible barrel assemblies, holders, fuel-tube and ignition parts, water-cooling components, powder-feed hardware, check valves, seals, O-rings and other JP5000 maintenance items.
|
Oxidizer
|
Oxygen (O2) |
|
Powder carrier gas
|
Inert gas, typically nitrogen or argon depending on process |
|
Gun type
|
Machine-mounted liquid-fuel HVOF spray gun |
|
Cooling medium
|
Water |
|
Cooling water pressure
|
100-150 psi (approx. 6.8-10.2 bar) |
|
Cooling water flow
|
7-12 gpm (approx. 26.5-45.4 l/min) |
|
Gun weight
|
Approx. 9.5 lb (4.3 kg), gun only |
|
Installation
|
Automated / robotic / machine-mounted HVOF systems |
|
Powder injection
|
Radial, downstream of the combustion-nozzle throat; dual-port configuration |
|
Sprayable materials
|
Carbides, cermets, metals, alloys and superalloys |
|
Fuel
|
Kerosene, typically K-1 / 1-K |
|
Reference architecture
|
JP5000 / Model 5220 type |
|
Combustion pressure
|
Up to 120 psig (8.2 bar) for the reference 5220 architecture |
|
Maximum powder spray rate
|
Up to 20 lb/h (approx. 151 g/min), material and parameter dependent |
|
Combustion-gas velocity
|
Up to 7,200 ft/s (approx. 2,190 m/s) in the reference gun design |
|
Barrel lengths
|
4 / 6 / 8 in (approx. 102 / 152 / 203 mm) |
|
Maximum kerosene flow
|
10.0 gph (approx. 37.9 l/h) |
|
Maximum oxygen flow
|
2,300 SCFH |
|
Gun dimensions
|
Approx. 16.5 x 6.25 x 3.25 in (419 x 159 x 83 mm) |
|
Typical inert-gas flow capacity
|
Up to 50 SCFH for the reference gun |
|
Process
|
High-Pressure High-Velocity Oxygen Fuel - liquid fuel (HVOF-LF) |
To purchase a product you like, you need to order it. There are several scenarios for how this can be done.
Choose the product you like and click the "Book now" button. When placing an order, fill out the form. Enter information in the fields: full name, phone number and e-mail. Then the manager will send you e-mail to confirm your consent to make the purchase.
If you have any questions related to the product select the product you like and click the "Ask a question" button. Then fill out the form with contact information and send an application. The manager will contact you for further discussion.
We work with legal entities. And we provide few payment options.
We work on Standard purchasing Contract basis. Payment type depends on product and final customer country/address.
If you have any questions related to the product select the product you like and click the "Ask a question" button. Then fill out the form with contact information and send an application. The manager will contact you for further discussion.
We can deliver your ordered goods with recommended logistic companies on EXW/DDP basis. Delivery time depends on final customer country/address. Terms and conditions can be found in invoice/offer.
Ready to delivery lead time is longer for customized equipment/systems.
If you have any questions related to the product select the product you like and click the "Ask a question" button. Then fill out the form with contact information and send an application. The manager will contact you for further discussion.


